American Fuel Dispenser Standards: Key Regulations and Specifications (English Overview)

U.S. fuel dispenser standards are governed by federal agencies, industry bodies, and technical specifications to ensure safety, accuracy, and environmental compliance. Below is a synthesis of critical standards and their requirements:

1. SAE ARP5904-2002**

Title: Aviation Fueling Systems - Icing Protection for Fueling Nozzles
Scope:

• Applies to aviation fueling nozzles used in aircraft refueling.
  Anti-Icing Design: Nozzles must prevent ice formation at temperatures ≤-40°C.
  

• Material Compatibility: Components must resist corrosion from aviation fuels (tested per ASTM D4868).

• Pressure Testing: Withstand 3× maximum operating pressure for 10 minutes without leakage.

2. FAA Part 23/25 - Certification Standards**

Title: Federal Aviation Regulations (FAR) for Aircraft Fuel Systems
Scope:

• Mandates safety compliance for aviation fuel dispensers and tanks.
  Leakage Limits: Fuel system leakage ≤0.1 mL/min under 1.5× maximum pressure.
  

• Fire Resistance: Enclosures must meet UL 94 V-0 flammability rating.

• Electrical Safety: Wiring systems comply with UL 427 for explosion-proof installations.

3. NIST Handbook 133**

Title: Checking the Net Contents of Packaged Commodities
Scope:

• Regulates accuracy requirements for retail fuel dispensers.
  Tolerance: ±0.3% for volume measurement (±0.5% for temperature-compensated systems).
  

• Repeatability: ≤0.1% error across three consecutive measurements.

4. UL 1203 - Standard for Safety**

Title: Explosion-Proof and Dust-Ignition-Proof Electrical Equipment
Scope:

• Applies to electrical components in explosive atmospheres (e.g., fueling stations).
  Enclosure Integrity: Must withstand 10 ft-lb impact without ignition.
  

• Temperature Limits: Surface temperatures ≤80% of autoignition temperature of fuels.

5. CSA C22.2 No. 22-M1986**

Title: Electrical Equipment for Use in Hazardous Locations
Scope:

• Certifies explosion-proof fuel dispensers and pumps.
  Zone Classification: Compliance with Zone 1/2 requirements (intrinsically safe or flameproof).
  

• Grounding: Resistance ≤10 Ω to prevent static discharge.

6. GMW 14859-2006**

Title: Fuel Fill Pipe and Opening - CARB Compliance
Scope:

• Ensures compatibility with California’s Stage II vapor recovery systems.
  Vapor Tightness: Fill pipes must limit vapor leakage to ≤15 mL during refueling.
  

• Material Stability: Resists ethanol-blend fuel degradation (tested per ASTM D4868).

7. ASME B31.3 - Process Piping**

Title: Process Piping Design and Installation
Scope:

• Guides fuel transfer piping in dispensers.
  Pressure Testing: Hydrostatic pressure tests at 1.5× design pressure.
  

• Corrosion Protection: Piping coatings must meet NACE MR0175 standards.

8. EPA 40 CFR Part 60**

Title: National Emission Standards for Hazardous Air Pollutants (NESHAP)
Scope:

• Limits volatile organic compound (VOC) emissions from fuel dispensers.
  Stage II Vapor Recovery: Mandatory for gasoline dispensers in ozone non-attainment areas.
  

• Leak Detection: Monthly monitoring of vapor recovery systems.

Compliance and Certification

• FAA Certification: Required for aviation fueling systems.

• CARB Compliance: Mandatory for dispensers in California.

• Testing Bodies: UL, CSA, and NSF International conduct conformity assessments.

Accessing Standards

1. Official Sources:

• Purchase from SAE International, FAA, or CSA Group.

2. Third-Party Translations:

•  China fuel dispenser (https://www.cnruijia.com),professional fuel dispenser manufacturer.

Key Differences from Non-U.S. Standards

For detailed implementation, refer to the full texts of SAE ARP5904, FAA FAR Part 23, and NIST Handbook 133.

上一篇：European Fuel Dispenser Standards

下一篇：没有了!